Data Dictionary

Overview

Change Log
Variable Dictionary
Calibration Dictionary
Global Constants
Template
Help

Sheet 1: Change Log

Shutdown Mechanisms - Rev 1				<- Global Program / Module Name
Revision	Author	Date	Change Description		Data Dictionary Type:	Component
1.0	OT	30-Jul-12	Initial Version

Sheet 2: Variable Dictionary

Shutdown Mechanisms - Rev 1

Variable Information

Range

Software Variable Name

Standard Reference Name

FDD Reference

Description

[I]nput [O]uput [M]oduleInternal [D]isplay [N]onVolatileMemory Usage

OEM

1X, 1Y, 1Z, 1I, 1BS 2X, 2Y, 2Z, 2I, 2BS etc Graph Settings

Initalization Value

Min

Max

Resolution

Unit Test Tolerance (+/-)

Units

Type

Memory Segment

Variables

ESMErrOutStat_Cnt_D_u08

ESMErrOutstat

FDD18 ShutdownMechanisms

status from the Error Signal Module

0.00E+00

Counts

uint8

SysFault2Stat_Cnt_D_u08

SysFault2Stat

FDD18 ShutdownMechanisms

status of the GPIO bit for the physical SYS_FAULT2 signal

0.00E+00

Counts

uint8

GateDrvResetStat_Cnt_D_u32

GateDrvResetStat

FDD18 ShutdownMechanisms

status of the GPIO bit for the physical Gate Drive Reset

524288

0.00E+00

Counts

uint32

NHETPwmStat_Cnt_D_u32

NHETPwmStat

FDD18 ShutdownMechanisms

status of the NHET control of the Gate Drive signals

22282308

0.00E+00

Counts

uint32

Sheet 3: Calibration Dictionary

Shutdown Mechanisms - Rev 1

Calibration Information

Achieved in Software Design

Range

Software Calibration Name

Standard Reference Name

FDD Reference

Description

Tuning Set

OEM

1X, 1Y, 1Z, 1I, 1BS 2X, 2Y, 2Z, 2I, 2BS etc Graph Settings

Default Value

Min

Max

Units

Type

Memory Segment

Calibrations

Sheet 4: Global Constants

Shutdown Mechanisms - Rev 1

Variable Information (Global Variables Only)

Achieved in Software Design

Used in Module List

Layer 2

Layer 3

Layer 4

Layer 5

Constant Name

Description

Uints

Type

Engineering Value

ADC

ADC Diagnostics

Data Memory Verification

DC Link Power Control

DSP Computational Integrity

DSP SPI driver

Event Manager Driver

External Memory Driver

Flash Programming Exec

GPIO

Illegal OpCode Handler

Interrupt Handler

Motor Current Driver

Motor Driver Diagnostics

Motor Position Driver

Phase Feedback Capture

Powerdown Control

Primary Shutdown Control

Program Flow

Program Memory Diagnostic

PWM Duty Cycle

Redundant Memory Check

Redundant Rapid Shutdown

Scheduler

Stack Monitor

State Dependent Task List

System Boot & Startup

System Control

Temperature Sensor Diagnostic

Unused Interrupt Handler

Utilization Monitor

Watchdog Dirver

Smith

Battery Voltage

Battery Voltage Diagnostics

Diagnostic CTC Manager

Diagnostic Manager

Diagnostics Application Services

EOL TorqueTest

Flash Boot Loader

Flight Recorder

Handwheel Position

Handwheel Torque

Motor Control Output Conversion

Motor Position Diagnostics

Motor Position Initialization

Motor Velocity

Motor Velocity Tachometer

Serial Communications I/O

Serial Communications Services

States and Modes

Tuning Select

Vehicle Power Mode

Vehicle Speed

Controller Polarity

Current Estimation

Handwheel Velocity

Inverse Motor Model

Motor Temperature Estimation

Motor Torque Limit

Output Reasonableness Dianostic

Parameter Estimation

Quadrant and rate Detection

Active Pull Compensation

Assist

Damping

Duty Cycle

Kinematic Integrity Diagnostic

Long Term Vehicle Speed Diagnostic

Max Assist Limit

Return

State Output Control

Torque Output

Sheet 5: Template

2.2a	Data File:

	Header:	extern <TYPE><TAB><NAME>;

	Source:	#pragma DATA_SECTION(<ROOTNAME>, "<SEGMENT>"); <TYPE> <NAME>;

	EOL Constants:

	Header:	extern <TYPE><TAB><NAME>;

	Source:	#pragma DATA_SECTION(<ROOTNAME>, "<SEGMENT>"); <TYPE> <NAME>;

	Global (Embedded) Constants:

	Header:	#define <NAME><COL40><VALUE>

	A2L Name

	Measurement:	rte_<SWC>_<NAME>

	Calibration Constants:

	Tuning ID:


	Tuning:	N	Index Range:

	Header:	extern CONST(<AUTOSAR_TYPE>, CAL_CONST) <NAME>;

	Source:	#pragma DATA_SECTION(<ROOTNAME>, ".<SEGMENT>"); CONST(<AUTOSAR_TYPE>, CAL_CONST) <NAME> = <VALUE>;

	eCal:	<NAME>



	Tuning:	Y	Index Range:

	Header:	<NONCRITICAL> #define <ROOTNAME><TAB>k_N_CalNC_Cnt_Str.<ROOTNAME> <NONCRITICAL> <SAFETYCRITICAL> #define <ROOTNAME><TAB>k_S_CalSC_Cnt_Str.<ROOTNAME> <SAFETYCRITICAL>

	Source:

	eCal:	<NONCRITICAL> k_N_CalNC_Cnt_Str.<ROOTNAME> <NONCRITICAL> <SAFETYCRITICAL> k_S_CalSC_Cnt_Str.<ROOTNAME> <SAFETYCRITICAL>



	Tuning:	P	Index Range:

	Header:	<NONCRITICAL> #define <ROOTNAME><TAB>k_N_CalNC_Cnt_Str.Personality[L3_S_CalPersSelect_Cnt_G_u16].<ROOTNAME> <NONCRITICAL> <SAFETYCRITICAL> #define <ROOTNAME><TAB>k_S_CalSC_Cnt_Str.SC_Personality[L3_S_CalPersSelect_Cnt_G_u16].<ROOTNAME> <SAFETYCRITICAL>

	Source:

	eCal:	<NONCRITICAL> k_N_CalNC_Cnt_Str.Personality[L3_S_CalPersSelect_Cnt_G_u16].<ROOTNAME> <NONCRITICAL> <SAFETYCRITICAL> k_S_CalSC_Cnt_Str.SC_Personality[L3_S_CalPersSelect_Cnt_G_u16].<ROOTNAME> <SAFETYCRITICAL>

Sheet 6: Help

Short cut	Macro	Sescription
Ctrl-q	ClearDataDictFilter	Will clear all autofilters on the Global Data Dictionary

	DFD_Create	Creates a Series of Data Flow Worksheet Pages from the information in the data dictionary. If Data Flow Worksheet pages already exist, they will be deleted first.
	DFD_Delete	Will clear all Data Flow Diagram pages from the Data Dictionary. This will make the file smaller for archiving.
	DFD_Print	Formate and prepares to print the Data Flow Worksheet pages.

Last modified October 12, 2025: Initial commit (0347a62)