AutoSAR FEE Parameter Configurations

                                                                            AutoSAR FEE Parameter Configuration (Rev 1.8)


AutoSAR FEE Parameter
Configuration Document

Texas Instruments Incorporated

                                                                          AutoSAR FEE Parameter Configuration (Rev 1.8)

ABSTRACT

AutoSAR  Flash  EEPROM  Emulation  (AutoSAR  FEE)  driver  utilizes  Code  Generation
Tool  to  generate  the  configuration  parameters  required  for  EEPROM  emulation.  Code
Generation  Tool  is  used  to  configure  parameters  like  which  Flash  Sectors  to  use,  the
number  of  Blocks,  Block  Size  etc.  for  EEPROM  emulation.  Code  Generation  Tool
generates two files (Fee_cfg.h & Fee_cfg.c) depending on the configuration.

This document describes the parameters used by Code Generation Tool to generate the
AutoSAR FEE Configuration parameters.

Texas Instruments Incorporated
2

                                                                          AutoSAR FEE Parameter Configuration (Rev 1.8)

Revision History

Version  Release
Author
Comment
Date
1.0
09/16/2012  Vishwanath  Initial version
Reddy
1.1
10/10/2012  Vishwanath  Add configuration parameter
Reddy
FEE_NUMBER_OF_VIRTUAL_SECTORS_EEP1
1.2
11/20/2012  Vishwanath  Remove FeeSetModeSupported
Reddy
1.3
06/11/2013  Vishwanath  Add configuration parameter’s:
Reddy
FEE_NUMBER_OF_UNCONFIGUREDBLOCKSTOCOPY,
FEE_NUMBER_OF_EIGHTBYTEWRITES
1.4
01/06/2014  Vishwanath  Added configuration parameter
Reddy
FEE_CHECK_BANK7_ACCESS
1.5
09/25/2014  Vishwanath  Configuration update to support TMS570LS05xx,
Reddy
TMS570LS07xx, TMS570LS09xx. Range updated for
FEE_VirtualSectorNumber, Virtual Sectors.
New configuration parameter
FEE_TOTAL_BLOCKS_DATASETS added.
1.6
12/31/2014  Vishwanath  Add new Configuration parameters.
Reddy
FEE_VIRTUALSECTOR_SIZE,
FEE_PHYSICALSECTOR_SIZE,
FEE_GENERATE_DEVICEANDVIRTUALSECTORSTRUC
Note added in section 1.6 FEE Sector Configuration.
1.7
01/07/2015  Vishwanath  Remove Device_Header.h from fee_cfg.h file.
Reddy
1.8
01/21/2015  Vishwanath  Added comments for FEE_TOTAL_BLOCKS_DATASETS,
Reddy
FEE_NUMBER_OF_EEPS and
FEE_NUMBER_OF_BLOCKS

Configuration Changes

Parameter added/ Modified
Change

FeeCRCEnable
New
FeeWriteCounterSave
New
FeeNumberOfEEPS
New
FeeDevErrorDetect
New
FeeBlockOverhead
Changed to 0x18
FeeEEPNumber(in block configuration)
New
FeeNumberOfVirtualSectorsEEP1
New
FEE_NUMBER_OF_UNCONFIGUREDBLOCKSTOCOPY
New

Texas Instruments Incorporated
3

                                                                          AutoSAR FEE Parameter Configuration (Rev 1.8)

FEE_NUMBER_OF_EIGHTBYTEWRITES
New
FEE_CHECK_BANK7_ACCESS
New
FEE_TOTAL_BLOCKS_DATASETS
New
FEE_VIRTUALSECTOR_SIZE
New
FEE_PHYSICALSECTOR_SIZE
New
FEE_GENERATE_DEVICEANDVIRTUALSECTORSTRUC  New

Texas Instruments Incorporated
4

                                                                          AutoSAR FEE Parameter Configuration (Rev 1.8)

1  Introduction
The  following  sections  describe  each  parameter  in  the  Fee_ParamDef.axml  file
used  by  Code  Generation  Tool  and  the  corresponding  configuration  parameter
generated.  Code  Generation  Tool  generates  two  files  (Fee_Cfg.c  and  Fee_cfg.h)
depending  on  the  configuration  values.  This  section  describes  each  configuration
value  in  the  above  two  files  and  their  relation  to  the  parameter  defined  in  the
Fee_ParamDef.axml file.
1.1  FEE Published information
1.1.1  Block OverHead
Parameter defined in

Fee_ParamDef.axml
FeeBlockOverhead

Description
Indicates the number of bytes used for Block
Header.

Generated configuration
FEE_BLOCK_OVERHEAD is set to the value
assigned to FeeBlockOverhead.

Default Value
0x18

Parameter Range
Fixed to 0x18.

Parameter Type
uint8

Target file
Fee_cfg.h
1.1.2  Maximum Blocking Time
Parameter defined in

Fee_ParamDef.axml
FeeMaximumBlockingTime

Description
Indicates the maximum allowed blocking time for any
Fee call.

Generated configuration
FEE_MAXIMUM_BLOCKING_TIME is set to the
value assigned to FeeMaximumBlockingTime.
Default Value
600.00

Parameter Range
Fixed to 600 µs.

Parameter Type
float
Target file
Fee_cfg.h

Texas Instruments Incorporated
7

                                                                          AutoSAR FEE Parameter Configuration (Rev 1.8)

1.1.3  Page OverHead
Parameter defined in

Fee_ParamDef.axml
FeePageOverhead

Description
Indicates the Page Overhead in bytes.

Generated configuration
FEE_PAGE_OVERHEAD is set to the value
assigned to FeePageOverhead. (0x0)

Default Value
0x0

Parameter Range
Fixed to 0x0.

Parameter Type
uint8

Target File
Fee_cfg.h
1.1.4  Sector OverHead
Parameter defined in

Fee_ParamDef.axml
FeeVirtualSectorOverhead

Description
Indicates the number of bytes used for Virtual Sector
Header.

Generated configuration
FEE_VIRTUAL_SECTOR_OVERHEAD is set to the
value assigned to FeeVirtualSectorOverhead (0x10).

Default Value
0x10

Parameter Range
Fixed to 0x10.

Parameter Type
uint8
Target File
Fee_cfg.h

Texas Instruments Incorporated
8

                                                                          AutoSAR FEE Parameter Configuration (Rev 1.8)

1.2  FEE General Settings
1.2.1  Virtual Page size
Parameter defined in

Fee_ParamDef.axml
FeeVirtualPageSize

Description
Indicates the virtual page size in bytes.

Generated configuration
FEE_VIRTUAL_PAGE_SIZE is set to the value
assigned to FeeVirtualPageSize. (0x8)

Default Value
0x8

Parameter Range
Fixed to 0x8.

Parameter Type
uint8

Target File
Fee_cfg.h

1.2.2   Driver Index
Parameter defined in

Fee_ParamDef.axml
FeeIndex

Description
Instance ID of FEE module. Should always be 0x0.

Generated configuration
FEE_INDEX is set to the value assigned to
FeeIndex. (0x0)

Default Value
0x0

Parameter Range
Fixed to 0x0.

Parameter Type
uint8

Target File
Fee_cfg.h

Texas Instruments Incorporated
9

                                                                          AutoSAR FEE Parameter Configuration (Rev 1.8)

1.2.3  Error Notification
Parameter defined in

Fee_ParamDef.axml
FeeNvmJobErrorNotification

Description
Call back function to notify a Job Error.

Generated configuration
FEE_NVM_JOB_ERROR_NOTIFICATION is set to
the defined function name. This is relevant only if
Polling mode is OFF.

Default Value
NvM_JobErrorNotification

Parameter Range
User defined function name.

Parameter Type
string

Target File
Fee_cfg.h


1.2.4  End Notification
Parameter defined in

Fee_ParamDef.axml
FeeNvmJobEndNotification

Description
Call back function to notify end of a Job.

Generated configuration
FEE_NVM_JOB_END_NOTIFICATION is set to the
defined function name. This is relevant only if Polling
mode is OFF.

Default Value
NvM_JobEndNotification

Parameter Range
User defined function name.

Parameter Type
string

Target File
Fee_cfg.h

Texas Instruments Incorporated
10

                                                                          AutoSAR FEE Parameter Configuration (Rev 1.8)

1.2.5  Frequency
Parameter defined in

Fee_ParamDef.axml
FeeFrequency

Description
Device operating frequency in MHz.

Generated configuration
FEE_OPERATING_FREQUENCY is set to the value
assigned to FeeFrequency.
FeeFrequency is equivalent to the HCLK frequency
in the TMS570 clock tree.
It is recommended to copy the value of HCLK
obtained by configuring the TMS570 clock tree
during MCU configuration to this parameter.

Default Value
160.0

Parameter Range
Device dependent parameter. Refer to the device
datasheet to know the range.

Parameter Type
float

Target File
Fee_cfg.h

1.2.6  Enable Polling mode
Parameter defined in

Fee_ParamDef.axml
FeePollingMode

Description
Indicates if polling mode is enabled/disabled.

Generated configuration
FEE_POLLING_MODE is set to STD_ON if polling is
enabled else it is set to STD_OFF. Currently, this
parameter should be always STD_ON.

Default Value
STD_ON

Parameter Range
STD_ON/STD_OFF

Parameter Type
Boolean

Target File
Fee_cfg.h

Texas Instruments Incorporated
11

                                                                          AutoSAR FEE Parameter Configuration (Rev 1.8)

1.2.7
Enable Error Correction
Parameter defined in

Fee_ParamDef.axml
FeeEnableErrorCorrection

Description
Indicates if error correction is enabled.

Generated configuration
FEE_FLASH_ERROR_CORRECTION_ENABLE
Is set to STD_ON if Error Correction is enabled else
it is set to STD_OFF. This parameter is not used
anymore.

Default Value
STD_OFF

Parameter Range
STD_ON/STD_OFF

Parameter Type
Boolean

Target File
Fee_cfg.h

1.2.8
Error Correction Handling
Parameter defined in

Fee_ParamDef.axml
FeeFlashErrCorrHandlingType

Description
Indicates desired action to be taken on detection of
bit errors.

Generated configuration
FEE_FLASH_ERROR_CORRECTION_HANDLING
is set to the value assigned to
FeeFlashErrCorrHandlingType. Only Fee_None is
supported.

Default Value
Fee_None

Parameter Range
Fee_None or Fee_Fix

Parameter Type
enum {Fee_none, Fee_Fix}

Target File
Fee_cfg.h

Texas Instruments Incorporated
12

                                                                          AutoSAR FEE Parameter Configuration (Rev 1.8)

1.2.9     Cyclic Redundancy Check

Parameter defined in

Fee_ParamDef.axml
FeeCRCEnable

Pre-processor switch to enable the CRC for blocks.
Description
STD_ON: CRC for blocks is enabled.
STD_OFF:CRC disabled

Generated configuration
FEE_FLASH_CRC_ENABLE is set to STD_ON if
CRC check is enabled else it is set to STD_OFF. If
enabled, 16 bit CRC of the block is generated.

Default Value
STD_OFF

Parameter Range
STD_ON / STD_OFF

Parameter Type
Boolean

Target File
Fee_cfg.h
1.2.10      Block Write counter save

Parameter defined in

Fee_ParamDef.axml
FeeWriteCounterSave

Pre-processor switch to enable the block write
Description
counter. STD_ON: Block Write counter is enabled.
STD_OFF:Block Write counter is disabled

Generated configuration
FEE_FLASH_WRITECOUNTER_SAVE is set to
STD_ON  if block write counter save is enabled else
it is set to STD_OFF.

Default Value
STD_OFF

Parameter Range
STD_ON / STD_OFF

Parameter Type
Boolean

Target File
Fee_cfg.h

Texas Instruments Incorporated
13

                                                                          AutoSAR FEE Parameter Configuration (Rev 1.8)

1.2.11      Number of EEPs

Parameter defined in

Fee_ParamDef.axml
FeeNumberOfEEPS

Number of EEP's configured. 1 - Only one EEP
Description
configured. All Virtual Sectors can be used by this
EEP. 2 - Two EEP's configured. Each EEP can use
two Virtual Sectors.

Generated configuration
FEE_NUMBER_OF_EEPS is set to 1 if all virtual
sectors are used by one EEP. If virtual sectors are
shared between two EEPs, it is set to 2.
Default Value
1
Parameter Range
1/2
Parameter Type
Uint8
Target File
Fee_cfg.h
Note: If GUI is calculating this parameter from the configuration, this parameter
may not be present in BSWMD file.
1.2.12  Development error Detect

Parameter defined in

Fee_ParamDef.axml
FeeDevErrorDetect

Pre-processor switch to enable and disable
Description
development error detection. true: Development
error detection enabled. false: Development error
detection disabled.

Generated configuration
FEE_DEV_ERROR_DETECT Is set to STD_ON if
Set Mode supported is required else it is set to
STD_OFF.

Default Value
STD_OFF

Parameter Range
STD_ON/STD_OFF

Parameter Type
boolean

Target File
Fee_cfg.h

Texas Instruments Incorporated
14

                                                                          AutoSAR FEE Parameter Configuration (Rev 1.8)

1.2.13  Non configured blocks to copy

Parameter defined in

Fee_ParamDef.axml
FeeNumberOfUnconfiguredBlocksToCopy

Defines the maximum number of non configured
Description
blocks to be copied during virtual sector swap. This
parameter is used if project configures and writes 10
blocks at start of the project, then reduce the number
of blocks to let’s say 8 blocks, but still want the other
two blocks to be present in Flash. In this case,
project should configure this parameter to 2.

Generated configuration
FEE_NUMBER_OF_UNCONFIGUREDBLOCKSTO
COPY is set to defined value.

Default Value
0

Parameter Range
0 -255

Parameter Type
Uint8

Target File
Fee_cfg.h

1.2.14  Number of eight byte writes

Parameter defined in
FeeNumberOfEightByteWrites
Fee_ParamDef.axml

Defines the number of 8 byte writes to be done in
Description
main function call. If configured to 2, main function
writes 16 bytes per call.

Generated configuration
FEE_NUMBER_OF_EIGHTBYTEWRITES is set to
defined value.

Default Value
1

Parameter Range
1-255

Parameter Type
Uint8

Texas Instruments Incorporated
15

                                                                          AutoSAR FEE Parameter Configuration (Rev 1.8)

Target File
Fee_cfg.h
1.2.15  Check BANK7 Address Range

Parameter defined in
FEE_CHECK_BANK7_ACCESS
Fee_ParamDef.axml

Pre processor switch to enable EEPROM address
Description
range check during read/write.

Generated configuration
FEE_CHECK_BANK7_ACCESS is set to defined
value.

Default Value
STD_OFF

Parameter Range
STD_ON/STD_OFF

Parameter Type
boolean

Target File
Fee_cfg.h
1.2.16  Total Blocks and Data Sets

Parameter defined in
FEE_TOTAL_BLOCKS_DATASETS
Fee_ParamDef.axml
Description
Macro to indicate total blocks and data sets
configured.
Generated configuration
FEE_TOTAL_BLOCKS_DATASETS is set to defined
value.
Default Value
1
Parameter Range
1-65536
Parameter Type
Uint16
Target File
Fee_cfg.h

Note: This configuration should calculate total number of blocks and data sets
configured in the structure Fee_BlockConfiguration. For example, if 5 blocks are
configured with block 1 has 1 data set, block 2 has 4 data sets, block 3 has 2
data sets, block 4 has 5 data sets, block 5 has 3 data sets, then
FEE_TOTAL_BLOCKS_DATASETS = [(1)+(4)+(2)+(5)+(3)] = 15(sum of all data
sets).
If GUI is calculating this parameter from the configuration, this parameter may
not be present in BSWMD file.

Texas Instruments Incorporated
16

                                                                          AutoSAR FEE Parameter Configuration (Rev 1.8)

1.2.17  Generate Device and Virtual sector structures
Parameter defined in
FEE_GENERATE_DEVICEANDVIRTUALSECTORS
Fee_ParamDef.axml
TRUC

Pre processor switch to enable/disable generation of
Description
Device and Virtual sector structures.

Generated configuration
FEE_GENERATE_DEVICEANDVIRTUALSECTORS
TRUC is set to defined value.

Default Value
STD_OFF

Parameter Range
STD_ON/STD_OFF

Parameter Type
boolean

Target File
Fee_cfg.h

Note: When this macro is turned ON, Fee_VirtualSectorConfiguration  and
Device_FlashDevice  are generated during run time.

Texas Instruments Incorporated
17

                                                                          AutoSAR FEE Parameter Configuration (Rev 1.8)

1.2.18  Required Virtual Sector Size

Parameter defined in
FEE_VIRTUALSECTOR_SIZE
Fee_ParamDef.axml

Macro to indicate the required virtual sector size in
Description
kilo bytes. This macro is only used when
FEE_GENERATE_DEVICEANDVIRTUALSECTORS
TRUC is STD_ON. Based on
FEE_VIRTUALSECTOR_SIZE and
FEE_NUMBER_OF_VIRTUAL_SECTORS, elements
of the structure Fee_VirtualSectorConfiguration will
be populated during runtime.

Generated configuration
FEE_VIRTUALSECTOR_SIZE is set to defined
value.

Default Value
None

Parameter Range
4-32(see below note)

Parameter Type
Uint8

Target File
Fee_cfg.h

Note: Depending on the device, parameter range can be different.
For TMS570LS12xx/11xx family devices, FEE bank is 4*16KB. Macro can take a
value of 16 or 32. For TMS570LS09xx, TMS570LS07xx, TMS570LS05xx family
devices, FEE bank is 16*4KB. Macro can take a value of 4 or 8 or 12 or 16 or 32.
FEE_VIRTUALSECTOR_SIZE * FEE_NUMBER_OF_VIRTUAL_SECTORS
should not exceed the total available FEE bank size on device.

Texas Instruments Incorporated
18

                                                                          AutoSAR FEE Parameter Configuration (Rev 1.8)

1.2.19  FEE bank Physical Sector Size

Parameter defined in
FEE_PHYSICALSECTOR_SIZE
Fee_ParamDef.axml

Macro to indicate the physical sector size on the
Description
device. This macro is only used when
FEE_GENERATE_DEVICEANDVIRTUALSECTORS
TRUC is STD_OFF. This parameter is used to select
device specific files.

Generated configuration
FEE_PHYSICALSECTOR_SIZE is set to defined
value.

Default Value
None.

Parameter Range
4/16

Parameter Type
Uint8

Target File
Fee_cfg.h

Note: This macro can only have 4/16 as value.
For TMS570LS12xx/11xx family devices, sector size is 16. For TMS570LS09xx,
TMS570LS07xx, TMS570LS05xx family devices, sector size is 4.

Texas Instruments Incorporated
19

                                                                          AutoSAR FEE Parameter Configuration (Rev 1.8)

1.3  Number of Blocks
1.3.1  Blocks
Parameter defined in

Fee_ParamDef.axml
FeeNumberOfBlocks

Description
Defines the number of Data Blocks used for
EEPROM emulation. This is sum of all the blocks
configured on EEP1 and EEP2.

Generated configuration
FEE_NUMBER_OF_BLOCKS is set to the defined
value.

Default Value
0x1

Parameter Range
0x1 to 0xFFFE

Parameter Type
uint16

Target File
Fee_cfg.h
Note: If GUI is calculating this parameter from the configuration, this parameter
may not be present in BSWMD file.

1.4  Number of Virtual Sectors
1.4.1  Virtual Sectors
Parameter defined in

Fee_ParamDef.axml
FeeNumberOfVirtualSectors

Description
Defines the number of Virtual Sectors used for FEE.

Generated configuration
FEE_NUMBER_OF_VIRTUAL_SECTORS is set to
the defined value.

Default Value
0x2

Min :0x2 Max : 0x4,For
Parameter Range
TMS570LS01227/TMS570LS1113.

Min : 0x2 Max : 16, For TMS570LS05xx,
TMS570LS07xx, TMS570LS09xx.

Parameter Type
uint16

Target File
Fee_cfg.h

Texas Instruments Incorporated
20

                                                                          AutoSAR FEE Parameter Configuration (Rev 1.8)

1.4.2  Virtual Sectors for EEP1
Parameter defined in

Fee_ParamDef.axml
FeeNumberOfVirtualSectorsEEP1

Description
Defines the number of Virtual Sectors used for
EEP1.

Generated configuration
FEE_NUMBER_OF_VIRTUAL_SECTORS_EEP1 is
set to the defined value.

Default Value
0x0

Parameter Range
Min : 0x0 Max :
(FEE_NUMBER_OF_VIRTUAL_SECTORS-0x02)

Parameter Type
uint16

Target File
Fee_cfg.h

Note: FEE_NUMBER_OF_VIRTUAL_SECTORS_EEP1 should be configured as
zero if FEE_NUMBER_OF_EEPS = 1.

1.5  FEE functions
1.5.1  FEE_GetVersionInfo
Parameter defined in

Fee_ParamDef.axml
FeeVersionInfoApi

Description
Indicates if the user can use the function
Fee_GetVersionInfo().

Generated configuration
FEE_VERSION_INFO_API is set to STD_ON if
FeeVersionInfoApi is enabled else it is set to
STD_OFF.

Default Value
STD_ON

Parameter Range
STD_ON / STD_OFF

Parameter Type
Boolean

Target File
Fee_cfg.h

Texas Instruments Incorporated
21

                                                                          AutoSAR FEE Parameter Configuration (Rev 1.8)

1.6  FEE Sector Configuration
Note: The structure definition Fee_VirtualSectorConfiguration in fee_cfg.c should
be under the conditional compile check
#if (FEE_GENERATE_DEVICEANDVIRTUALSECTORSTRUC == STD_OFF).
Projects need not configure below parameters when above macro is turned ON.
1.6.1  FEE_VirtualSectorConfiguration

Array Name
FEE_VirtualSectorConfiguration
Description
Used to define a Virtual Sector

Fee_VirtualSectorConfigType.
Array Type
This is a structure having the following members.

Members
FeeVirtualSectorNumber
Virtual Sector's Number.
EEPROM emulation is
FeeFlashBank
supported only on Bank 7 for
F021 devices..

FeeStartSector
Starting Sector in the Bank for
this Virtual Sector.

FeeEndSector
Ending Sector in the Bank for
this Virtual Sector.
The configurations described in the following sections are repeated for each
Virtual Sector.
1.6.1.1  FEE_VirtualSectorNumber
Parameter defined in

Fee_ParamDef.axml
FeeSectorNumber

Description
Used to assign a number to the Virtual Sector.

Generated configuration
FeeVirtualSectorNumber is set to the value assigned
to the symbolic name for the Virtual Sector.

Default Value
1

Parameter Range
Min : 0x1,  Max : 0x4,For
TMS570LS01227/TMS570LS1113

Min : 0x1 Max : 16, For TMS570LS05xx,
TMS570LS07xx, TMS570LS09xx

Parameter Type
uint16

Texas Instruments Incorporated
22

                                                                          AutoSAR FEE Parameter Configuration (Rev 1.8)

Target File
Fee_Cfg.c

1.6.1.2  FEE_VirtualSectorBank
Parameter defined in

Fee_ParamDef.axml
FeeSectorBank

Description
Indicates the Flash Bank used by the Virtual Sector.
All the Virtual Sectors should use the same Flash
Bank. EEPROM emulation is supported only on
Bank 7 for F021 devices.

Generated configuration
FeeFlashBank is set to the value assigned to
FeeSectorBank.

Default Value
0x7 for F021 devices.

Parameter Range
Fixed to 0x7 for F021 devices.

Parameter Type
uint16

Target File
Fee_Cfg.c
1.6.1.3   FEE_VirtualSectorStart
Parameter defined in

Fee_ParamDef.axml
FeeSectorStart

Description
Indicates the Flash Sector in the Bank used by the
Virtual Sector as the Start sector.

Generated configuration
FeeStartSector is set to the value assigned to
FeeSectorStart.

Default Value
0x0

Parameter Range
Device specific, can use any Sector of the selected
Flash Bank. Please refer to the device datasheet
“Flash Memory Map” for more details.

Parameter Type
uint8

Target File
Fee_Cfg.c

Texas Instruments Incorporated
23

                                                                          AutoSAR FEE Parameter Configuration (Rev 1.8)

1.6.1.4   FEE_VirtualSectorEnd
Parameter defined in

Fee_ParamDef.axml
FeeSectorEnd

Description
Indicates the Flash Sector in the Bank used by the
Virtual Sector as the End sector.

Generated configuration
FeeEndSector is set to the value assigned to
FeeSectorEnd.

Default Value
0x0

Parameter Range
Device specific, can use any Flash Sector of the
selected Flash Bank. It should be greater than the
FEE Start Sector. Please refer to the device
datasheet “Flash Memory Map” for more details.

Parameter Type
uint8

Target File
Fee_Cfg.c

Texas Instruments Incorporated
24

                                                                          AutoSAR FEE Parameter Configuration (Rev 1.8)

1.6.2  Example Virtual Sector Configuration
#if (FEE_GENERATE_DEVICEANDVIRTUALSECTORSTRUC == STD_OFF)
const Fee_VirtualSectorConfigType Fee_VirtualSectorConfiguration[] =
{
  /* Virtual Sector 1 */
  {
  1, /* Virtual sector number */
  7, /* Bank        */
  0, /* Start Sector *//*(0, For TMS570LS05xx, TMS570LS07xx, TMS570LS09xx)*/
  0, /* End Sector *//*(3, For TMS570LS05xx, TMS570LS07xx, TMS570LS09xx)*/
  },
  /* Virtual Sector 2 */
  {
  2, /* Virtual sector number */
  7, /* Bank          */
  1, /* Start Sector *//*(4, For TMS570LS05xx, TMS570LS07xx, TMS570LS09xx)*/
  1, /* End Sector *//*(7, For TMS570LS05xx, TMS570LS07xx, TMS570LS09xx)*/
  },
  /* Virtual Sector 3 */
{
  3,   /* Virtual sector number */
  7, /* Bank        */
  2, /* Start Sector *//*(8, For TMS570LS05xx, TMS570LS07xx, TMS570LS09xx)*/
  2, /* End Sector *//*(11, For TMS570LS05xx, TMS570LS07xx, TMS570LS09xx)*/
  },
  /* Virtual Sector 4 */
  {
  4, /* Virtual sector number */
  7, /* Bank         */
  3, /* Start Sector *//*(12, For TMS570LS05xx, TMS570LS07xx, TMS570LS09xx)*/
  3, /* End Sector   *//*(15, For TMS570LS05xx, TMS570LS07xx, TMS570LS09xx)*/
  },
};
#endif

Texas Instruments Incorporated
25

                                                                          AutoSAR FEE Parameter Configuration (Rev 1.8)

1.7  FEE Block Configuration
1.7.1  FEE Block Configuration

Array Name
Fee_BlockConfiguration
Description
Used to define a block

Fee_BlockConfigType.
Array Type
This is a structure with the following members.

Members
FeeBlockNumber
Indicates Block's Number.

FeeBlockSize
Defines Block's Size in bytes.

FeeImmediateData
Indicates if the block is used
for immediate data.
Number of write cycles
FeeNumberOfWriteCycles
required for this block .
FeeDeviceIndex
Indicates the device index.
Indicates the number of Datasets
FeeNumberofDatasets
for this Block.
FeeEEPNumber
Indicates the number of EEP.

The configurations described in the following sections are repeated for each
Block.
1.7.1.1  FEE_BlockNumber
Parameter defined in

Fee_ParamDef.axml
FeeBlockNumber

Description
Assigns a number for the Block.

Generated configuration
FeeBlockNumber is set to a numeric value. It is
equal to the BlockNumber.

Default Value
1

Parameter Range
Min : 0x1 Max : 0xFFFE

Parameter Type
uint16

Target File
Fee_Cfg.c

Texas Instruments Incorporated
26

                                                                          AutoSAR FEE Parameter Configuration (Rev 1.8)

1.7.1.2  FEE_BlockSize
Parameter defined in

Fee_ParamDef.axml
FeeBlockSize

Description
Indicates the size of the Block in bytes.

Generated configuration
FeeBlockSize is set to the value assigned to
FeeBlockSize.

Default Value
0x008

Parameter Range
0x1 to 0xFFFE

Parameter Type
uint16

Target File
Fee_Cfg.c

1.7.1.3  FEE_NumberOfWriteCycles
Parameter defined in

Fee_ParamDef.axml
FeeNumberOfWriteCycles

Description
Indicates the number of clock cycles required to write
to a flash address location.

Generated configuration
FeeNumberOfWriteCycles is set to the value
assigned to FeeNumberOfWriteCycles.

Default Value
0x1

Parameter Range
Device or core/flash tech dependent parameter.

Parameter Type
uint32

Target File
Fee_Cfg.c

Texas Instruments Incorporated
27

                                                                          AutoSAR FEE Parameter Configuration (Rev 1.8)

1.7.1.4  FEE_UseImmediateData
Parameter defined in

Fee_ParamDef.axml
FeeImmediateData

Description
Indicates if the block is used for immediate data.

Generated configuration
FeeImmediateData is set to the value assigned to
FeeImmediateData.

Default Value
FALSE

Parameter Range
TRUE / FALSE

Parameter Type
Boolean

Target File
Fee_Cfg.c

1.7.1.5  FEE Device Index

Parameter defined in

Fee_ParamDef.axml
FeeDeviceIndex

Description
Indicates the device index. This will always be 0.

Generated configuration
FeeDeviceIndex is set to the value 0x0.

Default Value
0x0

Parameter Range
Fixed to 0x0.

Parameter Type
uint8

Target File
Fee_Cfg.c

Texas Instruments Incorporated
28

                                                                          AutoSAR FEE Parameter Configuration (Rev 1.8)

1.7.1.6  FeeNumberOfDataSets
Parameter defined in

Fee_ParamDef.axml
FeeDataset

Description
Indicates the number of Datasets for this particular
Block .

Generated configuration
FeeNumberOfDataSets is set to the value assigned
to FeeDataset.

Default Value
0x01

Parameter Range
0x1 to 0xFF

Parameter Type
uint8

Target File
Fee_Cfg.c

1.7.1.7
FEE EEP Number

Parameter defined in

Fee_ParamDef.axml
FeeEEPNumber

Description
Number indicating into which EEP does the block go.
0 -- Block will be configured on EEP1. 1 -- Block will
be configured on EEP2.

Generated configuration
FeeEEPNumber is set to the value assigned.

Default Value
0x0

Parameter Range
0x00/0x01

Parameter Type
uint8

Target File
Fee_Cfg.c

Texas Instruments Incorporated
29

                                                                          AutoSAR FEE Parameter Configuration (Rev 1.8)

1.7.2  Example Block Configuration

/* Block Configuration */
const Fee_BlockConfigType Fee_BlockConfiguration[] =
{
  /* Block 1 */
  {
        0x01,
/* Block number
*/
        0x0010,
/* Block size

*/
        TRUE,
/* Block immediate data used
*/
        0x00000064,   /* Block number of write cycles   */
        0,
/* Device Index
*/
        1,

/* Number of DataSets

*/
        0

/* EEP number

*/
  },
  /* Block 2 */
  {
        0x02,
/* Block number
*/
        0x000B,
/* Block size

*/
        TRUE,
/* Block immediate data used      */
        0x00000064,   /* Block number of write cycles   */
        0,
/* Device Index
*/
    1,

/* Number of DataSets

*/
        1

/* EEP number

*/
  },
  /* Block 3 */
  {
        0x03,
/* Block number
*/
        0x000B,
/* Block size

*/
        TRUE,
/* Block immediate data used      */
        0x00000064,   /* Block number of write cycles   */
        0,
/* Device Index
*/
        1,

/* Number of DataSets

*/
        1

/* EEP number

*/
  },

  /* Block 4 */
  {
        0x04,
/* Block number
*/
        0x000B,
/* Block size

*/
        TRUE,
/* Block immediate data used      */
        0x00000064,   /* Block number of write cycles   */

Texas Instruments Incorporated
30

                                                                          AutoSAR FEE Parameter Configuration (Rev 1.8)

        0,
/* Device Index
*/
        1,

/* Number of DataSets

*/
        0

/* EEP number

*/
  },
};
1.8
Header Files

The following header files are included in the files generated by the Code
Generation Tool.
1.8.1
Header Files for Fee_cfg.h
The following files are included in Fee_cfg.h
1.  MemIf_Types.h
1.8.2
Header Files for Fee_cfg.c
The following files are included in Fee_cfg.c
1.  Fee.h
2.  Fee_Cbk.h
3.  SchM_Fee.h

This file should also include version check as following:

#if (FEE_AR_MAJOR_VERSION != 0x03)
  #error Fee_Cfg.c: FEE_AR_MAJOR_VERSION of Fee.h is incompatible.
#endif /* FEE_AR_MAJOR_VERSION */
#if (FEE_AR_MINOR_VERSION != 0x00)
  #error Fee_Cfg.c: FEE_AR_MINOR_VERSION of Fee.h is incompatible.
#endif /* FEE_AR_MINOR_VERSION */
#if (FEE_AR_PATCH_VERSION != 0x01)
  #error Fee_Cfg.c: FEE_AR_PATCH_VERSION of Fee.h is incompatible.
#endif /* FEE_AR_PATCH_VERSION */
#if (FEE_SW_MAJOR_VERSION != 1)
  #error Fee_Cfg.c: FEE_SW_MAJOR_VERSION of Fee.h is incompatible.
#endif /* FEE_SW_MAJOR_VERSION */
#if (FEE_SW_MINOR_VERSION != 20)
  #error Fee_Cfg.c: FEE_SW_MINOR_VERSION of Fee.h is incompatible.
#endif /* FEE_SW_MINOR_VERSION */
#if (FEE_SW_PATCH_VERSION != 0)
  #error Fee_Cfg.c: FEE_SW_PATCH_VERSION of Fee.h is incompatible.
#endif /* FEE_SW_PATCH_VERSION */

Texas Instruments Incorporated
31

Last modified October 12, 2025: Initial commit (0347a62)